DIY Rainbow 3D Origami Pencil Holder

5,009

72

12

About: I really enjoy the fabrics, the organization and the decoration.

Hello, in this tutorial I will teach you how to build a beautiful origami rainbow pencil holder, this pencil holder can be used to organize your desk implements and give freshness to your workspace.

Supplies:

Step 1: Materials

  • Colored paper: red, orange, yellow, green, blue and lilac.
  • Scalpel
  • Scissors
  • Compass
  • Pen
  • Foamy
  • Ruler

Step 2: Fold the Paper

Take a sheet on the longest side and bend 8 equal pieces, then take the sheet on the shortest side and divide it into 4 equal pieces as shown in the video.

Step 3: Cut the Sheet (1)

We take the 6 sheets of each color and cut with the scalpel through the guide lines along the shortest side of the sheet of paper.

Step 4: Cut the Sheet (2)

After cutting the 8 short pieces of each sheet of paper, with scissors cut each of the strips along the guide line.

Step 5: Creation of Origami Pieces

The size of the pieces is 3.7 cm wide by 5.5 cm long, fold the paper in half the longer side and then fold it back on the shorter side, then open and lift the lower ends as if we were making a paper plane, then turn the paper and then bend the tips towards the inside, finally the remainder we fold down and fold in half by the part that is closed as shown in the video.

Make 68 pieces of each color.

Step 6: Assembly of Parts for the Pencil Holder

We take one piece as a base and insert the other piece of the same tone above the first, then take the piece of the next color and insert it below and so consecutively interspersed.

Make the intercalation of each color four times, for example, you start with the yellow, orange, red, purple and blue pieces and finish with the green one.

Perform this combination 3 more times in order to close the base.

To make the body of the pencil holder they are assembled diagonally to the respective color.

In the following way, for example, the yellow piece has two small wings, place the other yellow piece in a yellow wing and the other pocket of the second yellow piece in the orange wing, as shown in the videos.

Step 7: Details

Once we have all the pieces assembled, we round up all the pieces with the end of a closed pen to embellish the pencil holder.

Step 8: Pencil Holder Base

Measure the diameter of the base, in this case 6 cm, and with the compass we make a circle a little smaller to this measure, then it is cut out and stuck with glue.

Thanks for reading and watching, if you liked this tutorial, consider voting for me, it would help me a lot.

Olivia.

Share

Recommendations

  • IoT Challenge

    IoT Challenge
  • Arduino Contest 2019

    Arduino Contest 2019
  • Classroom Science Contest

    Classroom Science Contest

12 Discussions

1
None
attosa

8 weeks ago

This is lovely! Great instructions, too. Voting :)

1 reply
1
None
WUVIE

2 months ago

This is amazing! Your intro photo definitely worked to get me to come inside and read more, and I'm glad I did.

Kudos for a fabulous Instructable!

1 reply
0
None
livy_jjjWUVIE

Reply 8 weeks ago

Thank you! I'm glad you enjoyed my Instructable. I hope you have the opportunity to make your own pencil holder.

2
None
celrobic

2 months ago on Step 8

This is beautiful! I can imagine it with many shades of the same color to create an ombre effect.

1 reply
0
None
livy_jjjcelrobic

Reply 2 months ago

Thank you very much! Of course! You can make the design you like, always going to be very nice.

0
None
livy_jjjItaliankiwiblog

Reply 2 months ago

Thank you very much! Yes, it is also very nice as a decoration for the home.

2
None
audreyobscura

2 months ago

Wow! This is an impressive technique! I was surprised to see it come together without any adhesive, except for the base at the bottom. Thanks for sharing!

1 reply
0
None
livy_jjjaudreyobscura

Reply 2 months ago

Super! It's cool that you liked it! Thanks for your comment.