TailLike

995

4

8

About: Building design/consulting in SE Minnesota. Resource based problem solver... in other words, I always take a minute to peek in construction dumpsters :) ---the way some have to workout everyday... i have to...

Meet TailLike!!

TailLike is an indicator that allows you to give a wave to cars behind you even at night. I find that during the long winters it's more difficult to give feedback to other drivers. Here's how to wave in any conditions!

---know that I've looked forward to making this instructable since I made a first model in 2015. There are a few photos mixed in from my current version and earlier prototypes. If you enjoy driving and find value I hope you'll try your hand at one!

Step 1: Materials & Tools

Materials

  • Coffee Can - ideally with a reflective inside finish and a transparent lid.
  • Wire (8-10') - low voltage wire rated for at least 12v. Ideally with two colors to track positive and negative.
  • 12v Outlet - buy new or cut up any old electronic. Ideally with a fuse and indicator light
  • Xmas Lights - any used incandescent or led works fine. --great if you can use the fused end
  • Switch - 2-pole rocker switch
  • Old Container - for switch housing (see steps 4+5)
  • Optional Film - any hobby store has translucent paper or tape. technically this is required to be street legal. you can't have any rear facing white lights. ---could also use red or blue xmas lights

Tools

----most of the materials are items i've salvaged over the years. I post a few links below but expect that most people who tinker with electronics already have these components. You can also easily get them from taking apart a few items from dollartree or goodwill.

Step 2: Wiring Diagram

The diagram shown in the photo is pretty simple.

  • Install the switch on the positive wire

Step 3: 12v Outlet

Prepare the 12v outlet by stripping the ends of the wires. I am using a salvaged adapter.

Yes. There is really only one detail to take away here. Important to track the positive and negative. I found it useful to have a 12v outlet that had the following features.

  • fused
  • indicator light (red led on the side)
  • red and black wires to recognize +/-

Step 4: Switch Housing (1 of 2)

Prepare the Switch Housing.
Anything work! I'm using an old pill container. It served me well as a container for tomato seeds.

  • Use a drill to open a hole in the cap to feed wire

---an easy follow up is to wrap any container in electrical tape

Step 5: Switch Housing (2 of 2)

Cut an opening for the switch. I had a rectangular rocker switch handy and paired it with a rectangular bottle. Pick the right one and take a few passes at opening the hole. Plastic cuts easy.

----the Olfa L-2 is possibly my favorite tool. It was most handy during architecture school and this one I've had for 10+ years

Step 6: Switch Connection

Here I'm using another salvaged component -- a coiled piece of cable. Not necessary but useful if you have one around.

Note that this is the first step where I am soldering. soldering is very simple and a great way to connect wires. I decided to solder because I am connecting small gauge wire to some larger pieces. typically my preference is to simply use electrical tape to wrap wires ---avoid caps whenever possible.

Solder only in a well ventilated space and take care to manage the heat and electricity.

Step 7: Soldering

Here is a look at my soldered connections. Any tips for connecting two different sized wires are certainly welcome. This is my approach and it works fine.

Step 8: Connected Wires

A look at the connected wires as compared to the wiring diagram. Note that the switch comes off it's only coiled wire connection.

--from here I wrapped the wires in electrical tape

Step 9: Christmas Lights

The Christmas Lights need to be connected in the direction of positive to negative electrical flow. Fortunately there are two indicators.

  1. The fuse of modern xmas lights is on the positive side
  2. The hinged clasp on each light points back in the positive direction

---these should be standard. Please check your own set. Know that if the lights are setup in reverse it is not dangerous. it simply wont turn on. Under 12v power it won't fry your bulbs.

Step 10: Can Prep (1 of 2)

Prepare the can for wires and lights.

  1. Punch an opening - I'm using a nail as a punch to open a hole at the base of the can
  2. Clean the opening - the needle nose works well to expand the hole and round down the edges

Wire connections happen inside the can. You could also open a larger hole and cover it with duct tape if you want to pass lights through that are already connected.

Step 11: Can Prep (2 of 2)

Adding a Thumb

  1. My approach is to simply google the facebook thumb. ---note the cover image has a thumb that is outlined. That is from an earlier model. I actually like the outlined model better but it's more difficult to see
  2. Trace an outline
  3. Fill it in

Step 12: Road Test + Enjoy!

Hope you've enjoyed this one!!

For years I've wanted to put together a kickstarter for the project. I love driving and always want to give feedback to other drivers on the road ---wonderful to be able to say thank you when someone lets you merge over.

Positive Feedback (only) - I've never turned the thumb upside down or drawn anything negative. Certainly suggest avoiding such behavior. You never know when your action is going to be the straw that sets someone else off.

Visibility. The thumb is clearly visible from 20-30 feet. Clearly visible when stopped or when flashed while passing.

Your Feedback - Any comments are certainly welcome.

Thank you! Jeff

Here are a few other recent projects:

Share

    Recommendations

    • Trash to Treasure

      Trash to Treasure
    • Arduino Contest 2019

      Arduino Contest 2019
    • Tape Contest

      Tape Contest

    8 Discussions

    0
    None
    TedA23

    3 months ago on Step 7

    Hiya!

    I want to recomend you to re-tin your soldering-tip.
    How do you clean the tip when soldering?

    If you have any questions, i will gladly help with you!

    Best regards
    Ted

    5 replies
    0
    None
    jprussackTedA23

    Reply 3 months ago

    Thanks! I simply wipe it on a scrap piece of 2x4... what should I be doing?

    0
    None
    TedA23jprussack

    Reply 3 months ago

    Follow the pictures in this order from start to you get the hang of it.

    WARNING!
    The white grindstone is really dangerous IF it brakes into dust and inhale! Contains high amount of Ammonium Chloride!! Use with care.

    WARNING!
    The Tip Activator, hazardous to inhail!

    IMG_20181230_170628.jpgIMG_20181230_171028.jpgIMG_20181230_171039.jpgIMG_20181230_171055.jpgIMG_20181230_171108.jpgIMG_20181230_171125.jpgIMG_20181230_171224.jpgIMG_20181230_171321.jpgIMG_20181230_171333.jpgIMG_20181230_171548.jpgIMG_20181230_172536.jpgIMG_20181230_172546.jpgIMG_20181230_172553.jpgIMG_20181230_173050.jpgIMG_20181230_173200.jpgIMG_20181230_173211.jpgIMG_20181230_173236.jpgIMG_20181230_173333.jpgIMG_20181230_173826.jpgIMG_20181230_173839.jpgIMG_20181230_174021.jpg
    0
    None
    TedA23jprussack

    Reply 3 months ago

    Evening! (atleast here in Sweden).

    At the moment i'm alone with my kids, and my wife is at work. When she is back home again, i can go down to the garage and power up my work bench and make a few pictures with instructions when it comes to clean and take care of the soldering tip and so on.

    0
    None
    TedA23TedA23

    Reply 3 months ago

    Back again.

    Starting off with some tips when it comes to soldering two different sizes of cabel.

    1) Never twin the copper strings on each cabel before joining them.

    2) Make sure the two cabels are the same lenght (read the naked copper strings).

    3) Join them, then twin them from only one side while the other side stay put between the fingertips.

    4) Add soldering paste (pure flux) with the tip of the soldering iron. This will make the tin soldering wire to get a better grip around the copper strings, and you will use much less soldering wire.

    5) Last step will be to use shrinktube, so the soldering part of the two cabels are secure and water proof.

    IMG_20181228_231056.jpgIMG_20181228_231309.jpgIMG_20181228_231337.jpgIMG_20181228_232023_1.jpgIMG_20181228_232355.jpgIMG_20181228_232815.jpg
    0
    None
    Kink Jarfold

    4 months ago on Step 12

    This has just been added to my to-do list. Excellent idea and very well done as an Instructable. --Kink--

    SEE WHAT KINK JUST POSTED, TONTO.png
    1 reply
    0
    None
    jprussackKink Jarfold

    Reply 4 months ago

    Thank you! Appreciate the support! Would enjoy knowing how you find it.