Hi,on step 10 you can see it on the first image. I soldered two XT60 connectors together to be able to attach both batteries. From the it goes directly do the esc and from there to the motors.
The case does not affect the voltage, but the motors :-DThe motors from V2 can only handle 2S. And even with just 2S the rover is crazy fast. The motors from V1 can handle 3S.
The main difference is voltage. 2S has 7.2v and 3S 11.1v.You can use 3x18650 batteries in series, so that you have 11.1v.
Hi Alexey,if you want to use those motors, than only V1 will work. V2 is a complete new design (although it looks identically) and those motors will not work. In Step 3 you can see how the new motors in this version will be mounted.
Pulley Driven Mini Table Saw
Table Saw for Kids
Hi Jonathan, I bought my LED 2 years ago at eBay for my first rover. I'll have a look if I find it in my list
ESP8266 WIFI AP Controlled Quadruped Robot
3D Printed Magnetic Levitation!
All in One Arcade System
DIY Controller for Paragliding Games
How to Spot Welding, Installing a BMS and Shrink Wrapping a Battery Pack.
Moonbunny As NightlightView Instructable »
No Weld Single Wheel Bike Trailer
DIY Sandblasting Cabinet and Etching Glass
How to Make a 3S 18650 Battery Pack
Arduino RC Amphibious Rover
FPV Rover V2.0
Wood Cutting Saw
Fusion Board - 3D Printed Electric Skateboard
RC Boat 3DBenchy
To view the FPV signal you need either a fpv-goggle (like this https://goo.gl/7gyVkt or this what I use https://goo.gl/7gyVkt) or a fpv-monitor like this https://goo.gl/7gyVkt
How to Make Remote Controlled Car
Hi, to control this I use a regular remote control (in my case the Taranis X9Dplus https://goo.gl/npDwJa).The FPV parts can be found on the BOM (camera, transmitter...)Depending on the things you want to use, you can add different components to the rover. For the first rover I built a rubber gun that can be used for V2.0 as well (https://www.thingiverse.com/thing:1269962), that needs two additional channels. My transmitter has 8 channels. You need 2 for driving and one for the tilt-mechanism. that would mean, that you could add 5 more things.In one of the last images you can see the space between the batteries. You can use that for additional electronics
Both depends on where you drive. With my previous Rover I had a Futaba remote control and the range wasn't that good. something about 60m-80m.With this V2.0 I use a Taranis. As this just finished this week, I couldn't test the range so far. Video should be a little bit more, if you don't have any obstacles between you and the rover.
Es ist keine spezielle Steuerung drinnen. Es ist nur ein Empfänger, in meinem Fall der V8FR II (https://goo.gl/JZphr9), drinnen. Gesteuert wird der Rover mit dem rechten Joystick und mit links kann ich die Camera steuern.
The printed parts should be about 15-20 Euros. Depending on your filament supplier. I pay 18€ for a 800g spool.Electronics depends on what you have and if you want to drive with FPV. If you already have a remote control and don't want to use FPV, the parts should be about 60€.
I use a taranis x9d plus. this is my remote control for almost everything
You're right. I just added the video to the top section :-D
Thank you. Took a while until it was ready. I had to redesign it from scratch due to migration to 540 motors
At the moment I run them with 2S and that is really powerful. I tried it once with 3S for short time and that is crazy. The ESC should handle that, the motors maybe not for long time
FPV Rover V2.0View Instructable »
3D Printed Willys RC 4X4