author
1Instructables198Views11CommentsJoined November 21st, 2016
did my fist instuctable
  • wolfmaker commented on Techgenie's instructable How to Make Electric Foam Cutter7 weeks ago
    How to Make Electric Foam Cutter

    i tried that would brake at where the glue was at maybe not doing it right i was also thinking of make a box frame with springs where i can pull down them move the frame back forth to guide the cut no need to to have steady hands as much. pull down how deep then some thing to Lock in place and a track to allow me to push or pull foreword and back, dimer switch so i can adjust the heat because if the wire gets too hot it cuts too easily and would like for a slower cuts to have more control in the over all cut to hard to explain how it will work

    View Instructable »
  • wolfmaker commented on diyperspective's instructable Acrylic Bending Tool7 weeks ago
    Acrylic Bending Tool

    nice i wish u make one that is for cutting Styrofoam i want to make a [_] hole in the thick foam keeping the part i gut out as the lid i have tried to just cut block and build the box but was not good foam braked where the glue was the best i could do is cutting with a utility knife the one where u can push out a long blade

    View Instructable »
  • wolfmaker commented on Techgenie's instructable How to Make Electric Foam Cutter4 months ago
    How to Make Electric Foam Cutter

    good idea I need to figure out how to make a modified version of this. what i want to do is cut out compartments with a big block of Foam and keep the block that would come out. what i trying to do is fit a cell phone in side the foam. normally i use a long knife like Utility Knife, the ones with the long blade that can stick out allot but it take many cuts. so i thinking how i can make it in one cut. so like sides bottom of it. then i should have a block of Foam then the phone would go in the Foam and the block would get a cut more then half in the long way to use as a lid over the cell phone then over that with another piece of Foam on top. size would be a big as the full block hard to say with worlds see pic to understand then u know what i mean. i did not add the extra piece of Foam...

    see more »

    good idea I need to figure out how to make a modified version of this. what i want to do is cut out compartments with a big block of Foam and keep the block that would come out. what i trying to do is fit a cell phone in side the foam. normally i use a long knife like Utility Knife, the ones with the long blade that can stick out allot but it take many cuts. so i thinking how i can make it in one cut. so like sides bottom of it. then i should have a block of Foam then the phone would go in the Foam and the block would get a cut more then half in the long way to use as a lid over the cell phone then over that with another piece of Foam on top. size would be a big as the full block hard to say with worlds see pic to understand then u know what i mean. i did not add the extra piece of Foam that goes over the top in the pic. but i think i might have a way if i make the width of the 2 side stick to be the same with as the phone width and instead of wire going side to side i'll try to make a wire going out to how deep of a hole i need maybe a thicker wire that is more stiff make a rectangle shaped wire i can push down in to the Foam then move forward then pull up at the other end so that i can cut it out in 1 cut see pic then u see what i trying to do and how i would modify it to do what i need it to do this is nice idea i hope my modification will work if thicker wire maybe more power as it take more power to heat the thicker wire

    View Instructable »
  • wolfmaker commented on gam cad's instructable Cat Enclosure1 year ago
    Cat Enclosure

    how does the net hold up i was going to use 72 inch by 100 foot 14 gauge 1 inch by 2 inch mesh galvanized welded wire because I'm worried that the cat might chew through the plastic netting as she like to chew on fish string i found her chewing on that i took it way from her as thinking that not good for her. im going to make a 12 feet wide x 20 feet front to back with extra panel 3 feet behind the front panel for extra door so that i can go inside and not worried that the cat get out on the street open the first door close it then open the next door if she get out its ok she still in the cat condo. cat condo is what i like to call it and i might add some run in later around the top side panels of the cat condo so she can go up high and look around

    View Instructable »
    • Peanut Butter Lid Mini Tripod  for Webcam and Small Cameras
      102 views
      1 favorites
      2 comments
  • Peanut Butter Lid Mini Tripod  for Webcam and Small Cameras

    i have pictures of it with the webcam on it this is a Logitech C930e USB Desktop or Laptop Webcam, HD 1080p Camerabut i do not have any set up like on a desk as i do not have a desk yet

    View Instructable »
  • The Single Most Effective Way to Get Rid of a Sunburn

    i use this solarcaine spray but first i lay in the tub with not hot and not cold water but a little bit colder than lukewarm for a very long time then i use the thishttps://www.walgreens.com/store/c/solarcaine-cool-aloe-burn-relief-formula-pain-relieving-spray-with-lidocaine/ID=prod5014-producthttps://pics.drugstore.com/prodimg/13328/450.jpg

    View Instructable »
  • wolfmaker commented on jordanuberalles's instructable Cat Trap2 years ago
  • wolfmaker commented on darbinorvar's instructable DIY String Light Chandelier for $402 years ago
    DIY String Light Chandelier for $40

    i want to do this with big bulb like 25 to 60 watts old round bulbs not florescent

    you can make a wizard cane get a clear Christmas ornament like this take off the wire and capof the glob get some glow sticks of the color that you like cute it open pore it in the the glob and keep adding more sticks init untill its full right to the neck but leave the neck most of it empty but still have a little pit in the neck then cut a piece of card board like the one form cereal box cut little circles that will fit inside the neck cut about 2 to 3 glue together then put some hot glue inside the neck close to the glowing chemical then put the piece of cardboard into the neck where you just had put hot glue at. try to put the piece of round cardboard as straight as possible then fill the rest of the neck with hot glue or epoxy glue now get 1 wooden rods then drill a hole the the t...

    see more »

    you can make a wizard cane get a clear Christmas ornament like this take off the wire and capof the glob get some glow sticks of the color that you like cute it open pore it in the the glob and keep adding more sticks init untill its full right to the neck but leave the neck most of it empty but still have a little pit in the neck then cut a piece of card board like the one form cereal box cut little circles that will fit inside the neck cut about 2 to 3 glue together then put some hot glue inside the neck close to the glowing chemical then put the piece of cardboard into the neck where you just had put hot glue at. try to put the piece of round cardboard as straight as possible then fill the rest of the neck with hot glue or epoxy glue now get 1 wooden rods then drill a hole the the top to the size of the glob neck when u drill the hole. drill only the length of the neck and diameter. then glue the glob in the rod now u have a Halloween wizard cane if u want the cane to look more authentic find a crooked cane like this https://img1.etsystatic.com/164/0/8055923/il_570x... then just drill a hole the size of the necks diameter and length of the globs neck and glue it in to the hole of the you made in the cane

    View Instructable »
  • wolfmaker commented on GordonKirkwood's instructable Telescoping Tube Clamps2 years ago
    Telescoping Tube Clamps

    so what size of tube and thicknes and iner tube size would i need to make a telescoping metal arm i want the out side tub to be 2 inch in diameter and 2 feet long and the second tub will be the same length 2 feet long but what diameter does the second tube need to be to fit inside of the tube the as far as the thickness of the 2 tubes i do not know how thick thy need to be but thy need to be able to hold up to 140 bl. of weight also the thicknes need to be thick enough to handel any side to side movement so that both tubes will not Bend or Warp because if it bends or warps to the side i will not be able to ajust the lengh of the tub any more

    View Instructable »